[URADI SAM] Zamena korone na Rolex Submariner-u!

Zanimljiv video i tutorijal kako sami da zamenite koronu na jednom Rolex sub-u, možda nekom bude od koristi! :)

http://www.youtube.com/watch?v=7Ev6D...layer_embedded

Sta sve covek moze da uradi svajcarskim nozicem. :)

Još jedan tutorijal...

Citat:

---

Jocke kaže:

Rolex bezel tutorial

Here I will try to show how you pull off the bezel, the insert and then put it back together again.


I start with this things at the working bench. A cloth, a knife, masking tape,a pair of gloves and of course a Rolex watch.

http://i842.photobucket.com/albums/z...-change-01.jpg

Here I start with the masking tape, just make sure you get it between the bezel and the case.

http://i842.photobucket.com/albums/z...-change-02.jpg

Then I put in the knife between the bezel and the case.

http://i842.photobucket.com/albums/z...-change-03.jpg

And just bend a little until it pop off.

http://i842.photobucket.com/albums/z...-change-04.jpg

Then I pull off the bezel and be careful so you don´t lose the spring at the 12 o´clock position.

http://i842.photobucket.com/albums/z...-change-05.jpg

Here is the backside of the bezel and you can see how it works.

http://i842.photobucket.com/albums/z...-change-06.jpg

Then I press with my thumbs from the backside of the bezel insert until it pop off.

http://i842.photobucket.com/albums/z...-change-07.jpg

And after that so will it looks like this.

http://i842.photobucket.com/albums/z...-change-08.jpg

Then I put back the bezel at the case with the spring at the inside.

http://i842.photobucket.com/albums/z...-change-09.jpg

Then I lay the bezel insert inside the bezel and look so it line up. Then I press it down at the bezel and when it´s there at more than the halfway round I pull off the complete bezel again.

http://i842.photobucket.com/albums/z...-change-10.jpg

---

Nastavak priče...

Citat:

---

Jocke kaže:

Now I can put the last part together nice and easy.

http://i842.photobucket.com/albums/z...-change-11.jpg

I do that at the same way as I do when I pull it off, just with my thumbs. No tools like pliers here, that will destroy the bezel insert.

http://i842.photobucket.com/albums/z...-change-12.jpg

Sometimes it dosen´t works and it´s a pain to get the last part in place. Then I use to put a cloth at the edge of the table and that will help you a lot. With that trick you can´t go wrong.

http://i842.photobucket.com/albums/z...-change-13.jpg

After that it´s ready for the watch and looks like this.

http://i842.photobucket.com/albums/z...-change-14.jpg

Then I put it over the spring nice and easy and look carefully so every part is in place.

http://i842.photobucket.com/albums/z...-change-15.jpg

Now it´s in place and as you can see it should be a little lower at the case so the crystal will be higher than the bezel.

http://i842.photobucket.com/albums/z...-change-16.jpg

Then I press down the bezel on both side at the same time until I hear a click. When you do that it´s in place. You can even see the crystal come out and the ratchet spring starts to work.

http://i842.photobucket.com/albums/z...-change-17.jpg

Now the only thing who is left is to see if it lines up.

http://i842.photobucket.com/albums/z...-change-18.jpg

It looks ok and if not, just do the same thing again.

Good luck and if you don´t feel safe to do the work, just let your watchmaker do it. I´m sure he do it for free.

I hope you have enjoy this trip and you can use the tips.

Jocke


Source: Jocke's Bezel Insert Tutorial

---